A15-9 REVISED SEPTEMBER, 2014 © Copyright 2023. All rights reserved. No portion may be copied or reproduced in any manner. SOSMETAL PRODUCTS INC. FASTENERS & HARDWARE A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 ROCK-ON FLAT PHILLIPS DRILL N’ TAP SCREWS (TEKS®) HIGH PERFORMANCE RIB HEAD DESIGN!!! l Rib design under head countersinks into dense material while preventing stripouts. l Two point types for steel and wood applications. l Larger head diameter increases board surface contact for greater pullover resistance. l #8 fastener has self-drilling point and standard thread. l #9 fastener has pointed tip and dual-spaced thread. l Head designed to countersink into any high-density panel, including cement board, tile backer board and plywood. l Thread design provides improved pull-out resistance. WALL LINER TORX® DRILL N’ TAP SCREWS (TEKS®) DESIGNED EXCLUSIVELY FOR TRAILER AND CONTAINER APPLICATIONS. l Torx® drive provides non-slip installation. l Larger wafer head style resists pullout. l Countersinks below plywood surface. l No pre-drilling necessary with Tek point. l Fast and easy one step installation. l Use T-25 torx driver. Cement-type boards Wire lath to steel Plywood to steel Brick ties to or steel any dense or wood studs. or wood studs. or wood studs. sheathings to steel or wood studs. Protected by LUSTERPLATETM against rust & corrosion * Fully threaded. HI-LO® PART NO. DIA.xLENGTH MATERIAL ATTACHMENT RANGE APPLICATIONS 505985* 9 x 1-1/4 Up to 3/4” material thickness to wood; 3/8”-1” material thickness to steel Cements board to 505986 9 x 1-5/8 Up to 1-1/8” material thickness to wood; wood or light gauge 3/8”-1-3/8” material thickness to steel steel 26-20 gauge 505987 9 x 2-1/4 Up to 1-3/4” material thickness to wood; 1” to 1-7/8” material thickness to steel TEK® PART NO. DIA.xLENGTH MATERIAL ATTACHMENT RANGE APPLICATIONS 505980* 8 x 1-1/4 3/8” to 3/4” material thickness Cements board 505981 8 x 1-5/8 3/8” to 1-1/4” material thickness to steel studs 505982 8 x 2-1/4 1” to 1-7/8” material thickness 20-12 gauge SIZE PART DIA.xTHRDxLNGTH NUMBER 10-16 x 1 505970 10-16 x 1-1/4 505971 Protected by CLIMACOAT against rust & corrosion HEX WASHER HEAD SLOTTED DRILL POINT SCREWS l Unique drill point speeds penetration and eliminates walking. No need to center punch. l Hardened steel point — drills its own hole. l Sharp threads prevent over-enlarging hole. Protected by LUSTERPLATETM against rust & corrosion LENGTH PART PART PART PART NUMBERQTY NUMBERQTY NUMBERQTY NUMBERQTY 3/8 53516 200 --- - --- - --- - 1/2 --- - 53517 200 53518 200 53519 200 3/4 --- - --- - --- - 53520 200 DIA. DIA. DIA. DIA. NO. 6 NO. 7 NO. 8 NO. 10 1/4” hex driver Part No. 53510 5/16” hex driver Part No. 53511 1/4” hex driver Part No. 53510 1/4” hex driver Part No. 53510 Includes Part No. 53510 1/4” hex driver Part No. 53505 201 pieces • 6 items 12032 plastic tray Numbers in assortment 53510 53516 53517 53518 53519 53520 DRILL N’ TAP SCREWS (TEKS®) and DRILL POINT SCREWS
RkJQdWJsaXNoZXIy MzE1MDc=